Alpha
-
Alpha 3 Flute HSS Cobalt Countersink 10.4mm
$NZ34.40Alpha HSS Cobalt 3 Flute 90° Countersink
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Three flute construction reduces chip load and controls chatter, which permits higher feed rates. Recommended machine use for accurate speed and feed rates for optimum results.
The Alpha three flute countersinks are the most multipurpose countersinks in the range
Suitable for countersinking all metals, plastics and wood
-
Alpha 3 Flute HSS Cobalt Countersink 12.4mm
$NZ40.10Alpha HSS Cobalt 3 Flute 90° Countersink
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Three flute construction reduces chip load and controls chatter, which permits higher feed rates. Recommended machine use for accurate speed and feed rates for optimum results.
The Alpha three flute countersinks are the most multipurpose countersinks in the range
Suitable for countersinking all metals, plastics and wood
-
Alpha 3 Flute HSS Cobalt Countersink 14.4mm
$NZ47.70Alpha HSS Cobalt 3 Flute 90° Countersink
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Three flute construction reduces chip load and controls chatter, which permits higher feed rates. Recommended machine use for accurate speed and feed rates for optimum results.
The Alpha three flute countersinks are the most multipurpose countersinks in the range
Suitable for countersinking all metals, plastics and wood
-
Alpha 3 Flute HSS Cobalt Countersink 16.5mm
$NZ63.10Alpha HSS Cobalt 3 Flute 90° Countersink
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Three flute construction reduces chip load and controls chatter, which permits higher feed rates. Recommended machine use for accurate speed and feed rates for optimum results.
The Alpha three flute countersinks are the most multipurpose countersinks in the range
Suitable for countersinking all metals, plastics and wood
-
Alpha 3 Flute HSS Cobalt Countersink 6.3mm
$NZ23.80Alpha HSS Cobalt 3 Flute 90° Countersink
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Three flute construction reduces chip load and controls chatter, which permits higher feed rates. Recommended machine use for accurate speed and feed rates for optimum results.
The Alpha three flute countersinks are the most multipurpose countersinks in the range
Suitable for countersinking all metals, plastics and wood
-
Alpha 3 Flute HSS Cobalt Countersink 8.3mm
$NZ30.20Alpha HSS Cobalt 3 Flute 90° Countersink
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Three flute construction reduces chip load and controls chatter, which permits higher feed rates. Recommended machine use for accurate speed and feed rates for optimum results.
The Alpha three flute countersinks are the most multipurpose countersinks in the range
Suitable for countersinking all metals, plastics and wood
-
Alpha Bi-Metal Multi-Tool Blade Tradesman Set – 4 piece
Original price was: $NZ71.20.$NZ60.00Current price is: $NZ60.00.Multi-tool Blade Set – 4 piece
The perfect starter kit to cut a wide range of materialsKit includes:
- 1 x Japanese Tooth Blade 32mm
- 1 x Japanese Tooth Blade 63mm
- 1 x Bi-Metal Blade 32mm
- 1 x Fine Tooth Blade 32mm
-
Alpha Cutting Disc – Stainless Steel Plus 125 x 1.0mm – 10 Pack Plastic Box
Original price was: $NZ79.90.$NZ55.00Current price is: $NZ55.00.The most advanced stainless cutting disc on the market.
New manufacturing technology has produced a disc with unparalleled performance and safety features that will maximise efficiencies and reduce costs in your stainless-cutting jobs.
Highest quality contaminant-free abrasive grain:
• Produces a cool clean cut and stops discolouring of the metal
Extra Strong Reinforcing and high rigidity:
• Produces precise, straight burr-free cuts
Made in Europe
-
Alpha Gold Series – Long Series Drill Metric 10.0mm
$NZ43.50The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 10.5mm
$NZ39.30The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 11.0mm
$NZ45.70The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 12.0mm
$NZ57.30The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 12.5mm
$NZ62.30The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 13.0mm
$NZ65.90The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 4.0mm
$NZ13.30The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 4.5mm
$NZ14.00The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 5.0mm
$NZ14.90The Alpha long series drills are Fully ground M2 HSS material that increases drill life| Titanium Nitride coating reduces heat and increases lubricity for extended life| 135ï¾° Split Point cuts faster and reduces wandering| Extra Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 5.5mm
$NZ14.40The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 6.0mm
$NZ15.80The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 6.5mm
$NZ15.40The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 7.0mm
$NZ16.60The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 7.5mm
$NZ22.60The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 8.0mm
$NZ26.10The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 8.5mm
$NZ32.10The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series – Long Series Drill Metric 9.0mm
$NZ38.50The Alpha Gold Series – Long Series Drills are:
- M2 HSS Fully ground M2 HSS material increases drill life
- Titanium Nitride coating reduces heat and increases lubricity for extended life
- 135° Split Point cuts faster and reduces wandering
- Longer Flute & overall length for drilling deeper holes
-
Alpha Gold Series HSS Impact Hex Drill Set 23 piece
Original price was: $NZ355.60.$NZ299.00Current price is: $NZ299.00.Alpha HSS Impact Hex Drill Set – Gold Series 23pc
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
• Sturdy plastic storage case
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 2.0mm
$NZ5.80Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 2.5mm
$NZ8.70Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 3.0mm
$NZ8.80Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 3.5mm
$NZ9.60Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 4.0mm
$NZ10.00Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 4.5mm
$NZ10.60Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 5.0mm
$NZ12.20Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 5.5mm
$NZ10.80Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%
-
Alpha Gold Series HSS Impact HEX Drive Drill Bit 8.0mm
$NZ17.00Alpha Gold Series HSS Impact HEX Drive Drill Bit
30% More Holes*
• Suitable for IMPACT DRIVERS & CORDLESS DRILLS
• 1/4″ QUICK CHANGE
• Titanium nitride coating reduces heat & increases lubricity for extended life
• 135° Split Point cuts faster & reduces wandering
• Fully ground M2 HSS raw material for extended life
• Ideal for the widest range of materials: Steel, Wood, Plastic and Stainless Steel
* Independent controlled testing has proved that the Alpha GOLD Series drills outperform other drills on the market by up to 30%.
-
Alpha Gold Series Jobber Drill Metric 10.00mm
$NZ15.10Alpha Gold Series 10.00mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 10.50mm
$NZ19.70Alpha Gold Series 10.50mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 11.00mm
$NZ19.30Alpha Gold Series 11.00mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 11.50mm
$NZ22.60Alpha Gold Series 11.50mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 12.00mm
$NZ21.30Alpha Gold Series 12.00mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 12.50mm
$NZ23.70Alpha Gold Series 12.50mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 13.00mm
$NZ26.50Alpha Gold Series 13.00mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 2.0mm
$NZ2.20Alpha Gold Series 2.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 2.5mm
$NZ2.30Alpha Gold Series 2.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 3.0mm
$NZ3.10Alpha Gold Series 3.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 3.5mm
$NZ2.90Alpha Gold Series 3.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 4.0mm
$NZ3.20Alpha Gold Series 4.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 4.5mm
$NZ4.20Alpha Gold Series 4.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 5.0mm
$NZ4.50Alpha Gold Series 5.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 5.5mm
$NZ5.90Alpha Gold Series 5.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 6.0mm
$NZ6.10Alpha Gold Series 6.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 6.5mm
$NZ5.10Alpha Gold Series 6.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 7.0mm
$NZ7.30Alpha Gold Series 7.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 7.5mm
$NZ8.80Alpha Gold Series 7.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 8.0mm
$NZ10.60Alpha Gold Series 8.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 8.5mm
$NZ12.40Alpha Gold Series 8.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 9.0mm
$NZ13.70Alpha Gold Series 9.0mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series Jobber Drill Metric 9.5mm
$NZ14.50Alpha Gold Series 9.5mm Jobber Drill Bit
When you go to buy a drill bit, what are you needing? Just a drill? or do you actually want HOLES?
Rigorous independent testing has proven that the Gold Series Drills outperform other Australian drills on the market by more than 30% – giving you more holes for your dollar in every single drill bit!
The Alpha Carded Gold series Drills boast the highest quality M2 HSS jobber drill!
-
Alpha Gold Series No.11 Gauge (4.85mm) Panel Drill Bit Double Ended
$NZ4.50Alpha Gold Series Gauge Panel Drill Bit Double Ended
The Alpha Gold Series Double Ended Panel Drills are Heavy Duty Industrial quality.
M2 HSS Fully ground M2 HSS material increases drill life
Available in Cobalt or HSS
Titanium Nitride Coating Increase’s hardness and decreases friction
135° split point eliminates the need for centre punches or pilot drilling
Suitable for drilling Plastic, wood and metal| including stainless steel.
-
Alpha Gold Series No.20 Gauge (4.09mm) Panel Drill Bit Double Ended
$NZ4.30Alpha Gold Series Gauge Panel Drill Bit Double Ended
The Alpha Gold Series Double Ended Panel Drills are Heavy Duty Industrial quality.
M2 HSS Fully ground M2 HSS material increases drill life
Available in Cobalt or HSS
Titanium Nitride Coating Increase’s hardness and decreases friction
135° split point eliminates the need for centre punches or pilot drilling
Suitable for drilling Plastic, wood and metal| including stainless steel.
-
Alpha Gold Series No.30 Gauge (3.26mm) Panel Drill Bit Double Ended
$NZ2.70The Alpha Gold Series Double Ended Panel Drills are Heavy Duty Industrial quality.
M2 HSS Fully ground M2 HSS material increases drill life
Available in Cobalt or HSS
Titanium Nitride Coating Increase’s hardness and decreases friction
135° split point eliminates the need for centre punches or pilot drilling
Suitable for drilling Plastic, wood and metal| including stainless steel.
-
Alpha Gold Series Step Drill Spiral Flute 4-12mm
Original price was: $NZ88.60.$NZ79.00Current price is: $NZ79.00.The Alpha Step Drills are premium industrial grade.
2 Flute Spiral Step Drill
4-12mmDrills & deburrs in one process
Ideal for: Non-ferrous metals, sheet steel, plastic & stainless steel up to 3mm thick
Suits: Non-hammer action portable power drillsSelf-starting split point removes the need for a pilot hole
2 flute design for smooth cutting
TiN coating reduces heat & increases lubricity for extended life
Laser etched hole
Premium HSS M2 raw material for extended life
3 flats on shank, prevents slippage in chuck
Bulk 1 piece convenient plastic pack
Technical information:
Number of steps: 9 steps
Step sizes: 4, 5, 6, 7, 8, 9, 10, 11 & 12mm
6.0mm shank
-
Alpha Gold Series Step Drill Spiral Flute 4-20mm
Original price was: $NZ118.70.$NZ99.00Current price is: $NZ99.00.The Alpha step Drills are premium industrial grade
2 Flute Spiral Step Drill
4-20mmDrills & deburrs in one process
Ideal for: Non-ferrous metals, sheet steel, plastic & stainless steel up to 3mm thick
Suits: Non-hammer action portable power drillsSelf-starting split point removes the need for a pilot hole
2 flute design for smooth cutting
TiN coating reduces heat & increases lubricity for extended life
Laser etched hole
Premium HSS M2 raw material for extended life
3 flats on shank, prevents slippage in chuck
Bulk 1 piece convenient plastic pack
Technical information:
Number of steps: 9 steps
Step sizes: 4, 6, 8, 10, 12, 14, 16, 18 & 20mm
8.0mm shank
-
Alpha Gold Series Step Drill Spiral Flute 6-30mm
Original price was: $NZ205.80.$NZ179.00Current price is: $NZ179.00.The Alpha step Drills are premium industrial grade
2 Flute Spiral Step Drill
6-30mmDrills & deburrs in one process
Ideal for: Non-ferrous metals, sheet steel, plastic & stainless steel up to 3mm thick
Suits: Non-hammer action portable power drillsSelf-starting split point removes the need for a pilot hole
2 flute design for smooth cutting
TiN coating reduces heat & increases lubricity for extended life
Laser etched hole
Premium HSS M2 raw material for extended life
3 flats on shank, prevents slippage in chuck
Bulk 1 piece convenient plastic pack
Technical information:
Number of steps: 13 steps
Step sizes: 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 & 30mm
10.0mm shank
-
Alpha Holesaw – Bi Metal 22mm
$NZ22.70Alpha White Pointer Bi-Metal holesaw
has been engineered for superior Heavy Duty cutting performance and accuracy.Heavy Duty stays sharper longer!
Bi-Metal construction with 8% cobalt welded teeth for extended life in industrial applications
40mm and over 3 ejection slots for rapid removal of thick and thin plugs
4/6 variable tooth configuration reduces vibration for a smooth, accurate cut
Unique multiple grinding technology for faster cutting and longer life
Multiple ejection slots for rapid removal of thick and thin plugs
International standard thread pattern accepts all common arbors
Manufactured to strict Alpha specifications to suit Heavy Duty conditions
Supplied in attractive hangable or free-standing 1pc card
-
Alpha Holesaw – Bi Metal 32mm
$NZ25.40Alpha White Pointer Bi-Metal holesaw
has been engineered for superior Heavy Duty cutting performance and accuracy.Heavy Duty stays sharper longer!
Bi-Metal construction with 8% cobalt welded teeth for extended life in industrial applications
40mm and over 3 ejection slots for rapid removal of thick and thin plugs
4/6 variable tooth configuration reduces vibration for a smooth, accurate cut
Unique multiple grinding technology for faster cutting and longer life
Multiple ejection slots for rapid removal of thick and thin plugs
International standard thread pattern accepts all common arbors
Manufactured to strict Alpha specifications to suit Heavy Duty conditions
Supplied in attractive hangable or free-standing 1pc card
Ideal for: Steel, stainless steel, cast iron, non-ferrous metal, wood and plastic
• Holesaw sizes up to 38mm dia: 38mm cutting depth
• Holesaw sizes 40mm dia and up: 48mm cutting depth
Alpha CDT cutting fluid (code: ATL005) is recommended for increased life when drilling steel.
-
Alpha Holesaw – Bi Metal 43mm
$NZ26.50Alpha White Pointer Bi-Metal holesaw
has been engineered for superior Heavy Duty cutting performance and accuracy.Heavy Duty stays sharper longer!
Bi-Metal construction with 8% cobalt welded teeth for extended life in industrial applications
40mm and over 3 ejection slots for rapid removal of thick and thin plugs
4/6 variable tooth configuration reduces vibration for a smooth, accurate cut
Unique multiple grinding technology for faster cutting and longer life
Multiple ejection slots for rapid removal of thick and thin plugs
International standard thread pattern accepts all common arbors
Manufactured to strict Alpha specifications to suit Heavy Duty conditions
Supplied in attractive hangable or free-standing 1pc card
Ideal for: Steel, stainless steel, cast iron, non-ferrous metal, wood and plastic
• Holesaw sizes up to 38mm dia: 38mm cutting depth
• Holesaw sizes 40mm dia and up: 48mm cutting depth
Alpha CDT cutting fluid (code: ATL005) is recommended for increased life when drilling steel.
-
Alpha Holesaw – Bi Metal 45mm
$NZ27.90Alpha White Pointer Bi-Metal holesaw
has been engineered for superior Heavy Duty cutting performance and accuracy.Heavy Duty stays sharper longer!
Bi-Metal construction with 8% cobalt welded teeth for extended life in industrial applications
40mm and over 3 ejection slots for rapid removal of thick and thin plugs
4/6 variable tooth configuration reduces vibration for a smooth, accurate cut
Unique multiple grinding technology for faster cutting and longer life
Multiple ejection slots for rapid removal of thick and thin plugs
International standard thread pattern accepts all common arbors
Manufactured to strict Alpha specifications to suit Heavy Duty conditions
Supplied in attractive hangable or free-standing 1pc card
Ideal for: Steel, stainless steel, cast iron, non-ferrous metal, wood and plastic
• Holesaw sizes up to 38mm dia: 38mm cutting depth
• Holesaw sizes 40mm dia and up: 48mm cutting depth
Alpha CDT cutting fluid (code: ATL005) is recommended for increased life when drilling steel.
-
Alpha Holesaw – Bi Metal 54mm
$NZ36.50Alpha White Pointer Bi-Metal holesaw
has been engineered for superior Heavy Duty cutting performance and accuracy.Heavy Duty stays sharper longer!
Bi-Metal construction with 8% cobalt welded teeth for extended life in industrial applications
40mm and over 3 ejection slots for rapid removal of thick and thin plugs
4/6 variable tooth configuration reduces vibration for a smooth, accurate cut
Unique multiple grinding technology for faster cutting and longer life
Multiple ejection slots for rapid removal of thick and thin plugs
International standard thread pattern accepts all common arbors
Manufactured to strict Alpha specifications to suit Heavy Duty conditions
Supplied in attractive hangable or free-standing 1pc card
-
Alpha Holesaw – Bi Metal 65mm
$NZ43.20Alpha White Pointer Bi-Metal holesaw
has been engineered for superior Heavy Duty cutting performance and accuracy.Heavy Duty stays sharper longer!
Bi-Metal construction with 8% cobalt welded teeth for extended life in industrial applications
40mm and over 3 ejection slots for rapid removal of thick and thin plugs
4/6 variable tooth configuration reduces vibration for a smooth, accurate cut
Unique multiple grinding technology for faster cutting and longer life
Multiple ejection slots for rapid removal of thick and thin plugs
International standard thread pattern accepts all common arbors
Manufactured to strict Alpha specifications to suit Heavy Duty conditions
Supplied in attractive hangable or free-standing 1pc card
Ideal for: Steel, stainless steel, cast iron, non-ferrous metal, wood and plastic
• Holesaw sizes up to 38mm dia: 38mm cutting depth
• Holesaw sizes 40mm dia and up: 48mm cutting depth
Alpha CDT cutting fluid (code: ATL005) is recommended for increased life when drilling steel.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 10.0mm
$NZ40.20Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 10.5mm
$NZ42.70Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 11.0mm
$NZ46.60Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 11.5mm
$NZ49.90Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 12.0mm
$NZ54.00Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 12.5mm
$NZ57.50Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 13.0mm
$NZ62.50Alpha ONSITE+ Impact Step Tip Drill Bit ¥ 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill ¥ Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer ¥ 1/4Ó Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers ¥ 135 degree split point – 135¡ split point cuts faster & reduces wandering ¥ M2 HSS – Fully ground M2 HSS raw material for extended life ¥ Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 3.0mm
$NZ22.30Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 3.5mm
$NZ23.00Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 4.0mm
$NZ23.80Alpha ONSITE+ Impact Step Tip Drill Bit ¥ 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill ¥ Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer ¥ 1/4Ó Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers ¥ 135 degree split point – 135¡ split point cuts faster & reduces wandering ¥ M2 HSS – Fully ground M2 HSS raw material for extended life ¥ Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 4.5mm
$NZ23.50Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 5.0mm
$NZ24.30Alpha ONSITE+ Impact Step Tip Drill Bit ¥ 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill ¥ Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer ¥ 1/4Ó Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers ¥ 135 degree split point – 135¡ split point cuts faster & reduces wandering ¥ M2 HSS – Fully ground M2 HSS raw material for extended life ¥ Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 5.5mm
$NZ24.70Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 6.0mm
$NZ25.50Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 6.5mm
$NZ25.70Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 7.0mm
$NZ26.70Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 7.5mm
$NZ27.30Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 8.0mm
$NZ29.80Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 8.5mm
$NZ32.90Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 9.0mm
$NZ35.30Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha ONSITE Plus Impact Step Tip Drill Bit 9.5mm
$NZ36.80Alpha ONSITE+ Impact Step Tip Drill Bit : 6x Speed – Fast, accurate drilling 6x FASTER than the benchmark competitor jobber drill
Unique Step Tip – Unique Step Tip design reduces heat & stays sharper for longer
1/4″ Quick Change – Easier & safer to use 1/4″ quick change shank with no jamming or binding. Suitable for Impact Drivers
135 degree split point – 135¡ split point cuts faster & reduces wandering
M2 HSS – Fully ground M2 HSS raw material for extended life
Round, precise holes without burring Alpha ONSITE+ Step Tip Drill was tested by our experts against the Benchmark Competitor Jobber Drill and blew the competition out of the water with speed, durability and accuracy. The competitor only drilled 2.5 holes in 1 minute and 46 seconds before burning out. Whereas the Alpha ONSITE+ Step Tip Drill Bit smashed out 3 perfect holes in just 21.83 seconds.
-
Alpha Reduced Shank Drill Bit 15.0mm Metric
$NZ63.50Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 16.0mm Metric
$NZ64.60Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 16.5mm Metric
$NZ65.50Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 17.0mm Metric
$NZ63.20Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 18.0mm Metric
$NZ74.20Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 19.0mm Metric
$NZ79.80Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 20.0mm Metric
$NZ89.70Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 21.0mm Metric
$NZ93.20Alpha Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Reduced Shank Drill Bit 25.0mm Metric
$NZ134.00Alpha 25mm Reduced Shank Drill Bit
• Black oxide coating maximises lubricant hold, therefore assisting chip flow and heat dissipation
• 3 flats on shank, prevents slippage in chuck
• 118º split point, ideal for drilling into pilot holes
Ideal for the widest range of materials: Steel, wood, plastic and stainless steel
-
Alpha Screw Extractor & Left Hand Cobalt Drill Set 10 piece
Original price was: $NZ126.50.$NZ99.00Current price is: $NZ99.00.Heavy Duty Left Hand Drills
• Sizes: 5/64″, 7/64″, 5/32″, 1/4″ & 19/64″
• 135º split point for extra gripping power
•Fully ground HSS Cobalt increases strength & drill life
For the removal of damaged screws, stud & bolts. Left hand drill bits remove fasteners or creates the pilot hole required for a screw extractor. If the LEFT HAND DRILL does not remove the fastener, the hole drilled becomes the preparation for a screw extractor. The opposite direction flute enables the broken fastener to be gripped and wound out of the hole. The opposite direction flute permits reverse drilling, which stops the fastener being driven tighter. Ensure drill is run in reverse
Screw Extractors
• Sizes: #1, #2, #3, #4 & #5
• Reverse tapered flute for extra gripping power
• Spiral tapered flute for deep embedment which increases grip as the resistance increases
• Square end for use with tap wrench or spanner
For the removal of damaged screws, stud & bolts. Left hand drill bits remove fasteners or creates the pilot hole required for a screw extractor. SCREW EXTRACTORS are engineered to remove the toughest damaged fasteners after the preparation of a pilot hole. The opposite direction flute enables the broken fastener to be gripped and wound out of the hole.
-
Alpha SDS Plus Zentro Masonry Drill 10 x 160mm
$NZ18.80The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 10 x 260mm
Original price was: $NZ27.20.$NZ24.00Current price is: $NZ24.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 12 x 210mm
Original price was: $NZ27.50.$NZ24.00Current price is: $NZ24.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 12 x 310mm
Original price was: $NZ42.80.$NZ35.00Current price is: $NZ35.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 16 x 260mm
Original price was: $NZ85.00.$NZ75.00Current price is: $NZ75.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 16 x 450mm
Original price was: $NZ100.10.$NZ85.00Current price is: $NZ85.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 18 x 250mm
Original price was: $NZ85.40.$NZ75.00Current price is: $NZ75.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 20 x 250mm
Original price was: $NZ91.00.$NZ79.00Current price is: $NZ79.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 22 x 250mm
Original price was: $NZ126.00.$NZ105.00Current price is: $NZ105.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 24 x 250mm
Original price was: $NZ88.40.$NZ75.00Current price is: $NZ75.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 5.0 x 110mm
Original price was: $NZ13.40.$NZ10.00Current price is: $NZ10.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|
The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel
Thanks to optimum 4 x 90° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel.
Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces
Centring tip for straight forward spot drilling with pinpoint accuracy
Four symmetrically functioning spiral ridges ensure low, uniform flute wear
Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance
The high-volume flute geometry ensures the optimum removal of drilling dust
4 Cutter head prevents seizing when drilling through reinforcing steel
Penetrates through steel deck plate e.g. Bondek and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 5.5 x 110mm
$NZ13.60The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 6.0 x 110mm
Original price was: $NZ12.70.$NZ10.00Current price is: $NZ10.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 6.5 x 110mm
Original price was: $NZ16.00.$NZ13.00Current price is: $NZ13.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 6.5 x 210mm
Original price was: $NZ28.40.$NZ25.00Current price is: $NZ25.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 8.0 x 160mm
Original price was: $NZ18.50.$NZ16.00Current price is: $NZ16.00.The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
Alpha SDS Plus Zentro Masonry Drill 8.0 x 210mm
$NZ21.10The Alpha ZENTRO Masonry range boasts dynamic drilling ability with secondary cutters protecting the drill bit in the event of reinforcement collision|The one-piece, solid carbide tip and patented reinforcing chamfering ensure low vibration and optimum drilling performance when drilling into reinforcing steel|Thanks to optimum 4 x 90ï¾° symmetry, all four carbide cutting edges function evenly and do not seize up on hitting reinforcing steel|Laterial support and maximum possible area of the interface between the carbide and steel body compensate for torsional forces|Centring tip for straight forward spot drilling with pinpoint accuracy|Four symmetrically functioning spiral ridges ensure low, uniform flute wear|Optimised flute core strength ensures low vibration drilling performance and exceptional fracture resistance|The high-volume flute geometry ensures the optimum removal of drilling dust|4 Cutter head prevents seizing when drilling through reinforcing steel|Penetrates through steel deck plate e.g. Bondekï¾® and concrete in one easy process
-
ALPHA Single Flute HSS Cobalt Countersink 10mm
$NZ25.30Alpha HSS Cobalt 1 Flute 90° Countersink
• Simple to sharpen by grinding the face of the flute
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Suitable for countersinking non-ferrous metals
Single flute construction provides less aggressive and slower cutting than multi-flutes, therefore reducing the risk of chattering permitting optimum performance for the handyman and portable power tools
-
Alpha Single Flute HSS Cobalt Countersink 16mm
$NZ43.40Alpha HSS Cobalt 1 Flute 90° Countersink
• Simple to sharpen by grinding the face of the flute
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Suitable for countersinking non-ferrous metals
Single flute construction provides less aggressive and slower cutting than multi-flutes, therefore reducing the risk of chattering permitting optimum performance for the handyman and portable power tools
-
Alpha Single Flute HSS Cobalt Countersink 20mm
$NZ57.40Alpha HSS Cobalt 1 Flute 90° Countersink
• Simple to sharpen by grinding the face of the flute
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Suitable for countersinking non-ferrous metals
Single flute construction provides less aggressive and slower cutting than multi-flutes, therefore reducing the risk of chattering permitting optimum performance for the handyman and portable power tools
-
Alpha Single Flute HSS Cobalt Countersink 25mm
$NZ74.80Alpha HSS Cobalt 1 Flute 90° Countersink
• Simple to sharpen by grinding the face of the flute
• Fully ground M42 HSS-Co8 increases strength and countersink life
• Suitable for countersinking non-ferrous metals
Single flute construction provides less aggressive and slower cutting than multi-flutes, therefore reducing the risk of chattering permitting optimum performance for the handyman and portable power tools
-
Alpha TCT Countersink 2.8mm
$NZ46.10Ideal for Timber Decking & Cement Sheet
• Tungsten carbide tipped pilot drill with improved chip extraction, allowing increased feed rates & shorter cycle times
• Adjustable depth stop suitable for flush mounting & deep enough to accommodate a plug
• Packaged with grub screw for replacing drill
Countersink Features:
• 90° Angle
• Three flutes
• Tungsten Carbide Tipped
-
Alpha TCT Countersink 3.0mm
$NZ50.90Ideal for Timber Decking & Cement Sheet
• Tungsten carbide tipped pilot drill with improved chip extraction, allowing increased feed rates & shorter cycle times
• Adjustable depth stop suitable for flush mounting & deep enough to accommodate a plug
• Packaged with grub screw for replacing drill
Countersink Features:
• 90° Angle
• Three flutes
• Tungsten Carbide Tipped
-
Alpha TCT Countersink 3.5mm
$NZ54.60Ideal for Timber Decking & Cement Sheet
• Tungsten carbide tipped pilot drill with improved chip extraction, allowing increased feed rates & shorter cycle times
• Adjustable depth stop suitable for flush mounting & deep enough to accommodate a plug
• Packaged with grub screw for replacing drill
Countersink Features:
• 90° Angle
• Three flutes
• Tungsten Carbide Tipped
