HANDTOOLS
-
PICA VISOR LONGLIFE BOARD MARKER RED
VISOR Longlife Board Marker “DRY-ERASE Crayon” for Industry and Office. THE MARKER, WHICH NEVER DRIES OUT. For industrial use, especially for temporary marking on all glossy material surfaces. For office-use, especially on whiteboard and flip chart at the same time.
-
POWERBUILT 1/2” Dr 30pc 6pt Metric Standard Dual Impact Socket Sets
Thin wall design, impact rated
Use with both impact and hand tools
Chrome molybdenum steel, black finish
Offers Z-Drive contacting the flat walls of fasteners for stronger grip
Packaged in a metal storage case
½” Dr Industrial Gear to Gear Ratchet (45T)
Sockets (6pt) 10mm, 11mm, 12mm, 13mm, 14mm, 15mm, 16mm, 17mm, 18mm, 19mm, 20mm, 21mm, 22mm, 23mm, 24mm, 25mm, 26mm, 27mm, 28mm, 29mm, 30mm, 32mm, 33mm, 34mm, 35mm, 36mm
Extension bars 75mm & 150mm -
RENNSTEIG PARALLEL PIN PUNCH -150 X 4MM
- Used for removing pins in parallel holes. Designed to punch holes when struck by a hammer
- High bending resilience for longer service life and higher elasticity
- Ground and polished surface
- Rennsteig punches are made of chrome vanadium steel
- Forged, quenched and tempered as a whole to guarantee good resiliency and long service life
- Made in Germany
-PICTURE SHOWN NOT ACTUAL SIZE
-
RENNSTEIG PARALLEL PIN PUNCH -150 X 6MM
- Used for removing pins in parallel holes. Designed to punch holes when struck by a hammer
- High bending resilience for longer service life and higher elasticity
- Ground and polished surface
- Rennsteig punches are made of chrome vanadium steel
- Forged, quenched and tempered as a whole to guarantee good resiliency and long service life
- Made in Germany
-
STABILA 96-2-1200 1200MM SPIRIT LEVEL
On site a level can get dropped and has to take a lot of hard wear. So, it’s important that the level stays accurate job after job. With two vertical vials it helps you take a reading in any position. The tough reinforced aluminum profile, together with the STABILA locked vial system is the ideal combination on any harsh building site. Because the purpose of our levels is to be accurate and stay accurate.
-
STABILA 96-2-600 600MM SPIRIT LEVEL
On site a level can get dropped and has to take a lot of hard wear. So, it’s important that the level stays accurate job after job. With two vertical vials it helps you take a reading in any position. The tough reinforced aluminum profile, together with the STABILA locked vial system is the ideal combination on any harsh building site. Because the purpose of our levels is to be accurate and stay accurate.
-
STANLEY® 1991 Utility Blade (Pack Of 5)
- STANLEY® Original 1991 utility knife blade for every-day, general purpose use.
- EVERY DAY GENERAL USE: The 1991 blade is suitable for cutting most light sheet materials, paper and cardboard.
- SHARP, DURABLE DESIGN: Hardened and tempered for high sharpness and long life.
-
STANLEY® 99E Classic Retractable Blade Utility Knife
- STANLEY® 99E Classic Retractable Blade Utility Knife – STANLEY’s original retractable utility knife since 1952.
- DURABLE DESIGN: Precision die cast zinc body both strong and lightweight
- ACCURATE CUTTING: InterLock® nose firmly secures the blade into the knife for safe, accurate cuts
-
STANLEY® DYNAGRIP® Combination Pliers (200mm)
- HEAVY DUTY CONSTRUCTION: Manufactured from drop-forged steel for strength and durability
- CORROSION-RESISTANT: Black oxide finish helps resist corrosion for extended product life
- THREE-ZONE HANDLE: Ergonomically designed Three-Zone Bi-material grips for comfort and control
-
STANLEY® FATMAX® Automatic Wire Stripper
- AUTOMATIC WIRE STRIPPER: For copper or aluminum cables up to 10mm² (multiple cables) and up to 6mm² (single cables)
- ERGONOMIC GRIP AND MORE EFFICIENCY: Possibility of stripping wires with a diameter of 0.2 to 6mm² – The pliers automatically adjust their jaws to the diameter of the wire
- ADJUSTABLE WIRE STOP: Adjustments via fine adjustment screw
-
STANLEY® FATMAX® BladeArmor™ 10M (32mm wide) Tape Measure
- DURABLE BLADE: Abrasion resistant polyester film coated blade coating provides up to 10 times more resistance to abrasion than a standard lacquered blade, increasing the life of the tape and reducing wear on most heavily used sections of the blade.
- BladeArmor™ Coating: reinforces the first 7.5cm of the blade, the section most vulnerable to wear.
- GREATER REACH: 32mm blade width and extended reach of 4.2 metres to help you measure confidently from a distance, even when working alone.
-
STANLEY® FATMAX® BladeArmor™ 8M (32mm wide) Tape Measure
- DURABLE BLADE: Abrasion resistant polyester film coated blade coating provides up to 10 times more resistance to abrasion than a standard lacquered blade, increasing the life of the tape and reducing wear on most heavily used sections of the blade.
- BladeArmor™ Coating: reinforces the first 7.5cm of the blade, the section most vulnerable to wear.
- GREATER REACH: 32mm blade width and extended reach of 4.2 metres to help you measure confidently from a distance, even when working alone.
-
STANLEY® FATMAX® BladeArmor™ Magnetic 8M (32mm wide) Tape Measure
- DURABLE BLADE: Abrasion resistant polyester film coated blade coating provides up to 10 times more resistance to abrasion than a standard lacquered blade, increasing the life of the tape and reducing wear on most heavily used sections of the blade.
- BladeArmor™ Coating: reinforces the first 7.5cm of the blade, the section most vulnerable to wear.
- GREATER REACH: 32mm blade width and extended reach of 4.2 metres to help you measure confidently from a distance, even when working alone.
-
STANLEY® FATMAX® Left Cut Aviation Snips
- STANLEY® FATMAX® Left Cut Aviation Snips with compound cutting action and serrated cutting blades cut up to 18-gauge cold rolled or 23-gauge stainless steel
- DOUBLE PIVOT ACTION: Higher cutting power
- FORGED CHROME MOLYBDENUM STEEL CUTTING BLADES: For strength and durability
-
STANLEY® FATMAX® Left Cut Offset Aviation Snips
- STANLEY® FATMAX® Left Cut Offset Aviation Snips with compound cutting action and serrated cutting blades cut up to 18-gauge cold rolled or 23-gauge stainless steel
- DOUBLE PIVOT ACTION: Higher cutting power
- OFFSET ANGLED BLADES: Provide clearance between the handles and the cutting material
-
STANLEY® FATMAX® Right Cut Aviation Snips
- RIGHT CUT AVIATION SNIPS: With compound cutting action and serrated cutting blades cut up to 18-gauge cold rolled or 23-gauge stainless steel
- DOUBLE PIVOT ACTION: Higher cutting power
- FORGED CHROME MOLYBDENUM STEEL CUTTING BLADES: For strength and durability
-
STANLEY® FATMAX® Right Cut Offset Aviation Snips (Green)
- RIGHT CUT OFFSET AVIATION SNIPS: With compound cutting action and serrated cutting blades cut up to 18-gauge cold rolled or 23-gauge stainless steel
- DOUBLE PIVOT ACTION: Higher cutting power
- OFFSET ANGLED BLADES: Provide clearance between the handles and the cutting material
-
STANLEY® FATMAX® Screwdriver Regular Ratchet with 12 Bits
- FINE 45-TOOTH RATCHET: Delivers extremely high torque with a 9° working arc
- BI-MATERIAL HANDLE: For grip, comfort and high torque loads
- INTERNAL BIT STORAGE: For safe and easy bit storage – keeps bits close to hand
- MAGNETIC HEAD: Enables efficient bit retention and rapid changing of accessories and prevents bit loss
- 3 POSITION RATCHET: Enables clockwise, anti-clockwise and locked ratcheting positions with left, right and central fixed options
- ROBUST FROSTED BAR: Ensures outstanding product life
-
STANLEY® FATMAX® Side Strike Wood Chisel (25mm)
- STANLEY® FATMAX® Sidestrike Wood Chisel features NEW cutting edge on side of the blade for demolition Work, also allowing the chisel to double as a spokeshave
- Hardened, tempered carbon chrome steel blade for edge retention
- Sharpened side edge for chopping out, cutting, shaving and shaping
- Hardened strike cap and strike surface for durability
- Bi-Material handle for grip and comfort
- Steel core for strength & durability
-
STANLEY® FATMAX® Straight Cut Aviation Snips
- STANLEY® FATMAX® Straight Cut Aviation Snips with compound cutting action and serrated cutting blades cut up to 18-gauge cold rolled or 23-gauge stainless steel
- DOUBLE PIVOT ACTION: Higher cutting power
- FORGED CHROME MOLYBDENUM STEEL CUTTING BLADES: For strength and durability
-
STANLEY® FATMAX® Thru Tang Wood Chisel 6 Piece Set (6,12,18,25,32,38mm)
- STANLEY® FATMAX® Thru-Tang Wood Chisels are 50% stronger than old DynaGrip Pro Chisel on handle side impact test
- Hardened, tempered high-chrome carbon alloy steel blade for edge retention
- Ergonomic Bi-Material soft grip handle – for maximum grip and control
-
STANLEY® FATMAX® TradeLift™
- GET MORE DONE – SOLO: Ideal for jobs where one person isn’t quite enough, with heavy-duty performance delivering up to 150kg lifting force with up to 220mm lifting capacity
- MULTIPLE TRADE APPLICATIONS: Lifts, levels, holds and spreads easily and safely for multiple applications across kitchen, floor, door and window fitting, carpentry, joinery, drywall and general construction work
- FOOT OPERATION FOR EASY HANDS-FREE LIFTING: Safe and easy to use, reducing the risk of injury and accidents when levelling and holding heavy or awkward items such as sheet materials, doors and large appliances
-
STANWAY 180mm Aluminium Rafter Square
This trade quality 180mm Stanway Aluminium Rafter Square is precision designed and made from aluminium to ensure strength, durability, and long life. CNC machined edges for guaranteed accuracy. This rafter square has a anodized matte black protective finish with easy-to-read laser etched bold white markings. This square uses metric millimetre markings/measurements. A common rafter conversion table is included on rafter square which has been laser etched on one side. Suitable for all trades people and the serious DIY users.
-
STANWAY 250mm Flat Bastard Cut File
Flat file type with bastard cut used for general purpose deburring, sharpening and shaping. For use on iron and steel. Double cut on sides and Single cut on edges.
Specifications:
- Overall Length: 365mm
- Blade Length: 250mm
- Blade Width: 24mm
- Blade Depth: 5.5mm
- Handle Length: 115mm
- Handle Width: 30mm
- Handle Depth: 25mm
-
STANWAY 250mm Half Round Bastard Cut File
Used for flat, convex and concave surfaces. Double cut used with slightly heavier pressure that removes material faster. Bastard cut for general purpose deburring, sharpening and shaping.
Specifications:
- Overall Length: 365mm
- Blade Length: 250mm
- Blade Width: 24mm
- Blade Depth: 7mm
- Handle Length: 115mm
- Handle Width: 30mm
- Handle Depth: 25mm
-
STANWAY 250mm Half Round Wood Rasp File
Half round in shape for flat, convex and concave surfaces. Used on materials such as wood and soft metals. Has a much coarser rasp-type surface, for rapid removal and shaping.
Specifications:
- Overall Length: 365mm
- Blade Length: 250mm
- Blade Width: 24.5mm
- Blade Depth: 7mm
- Handle Length: 115mm
- Handle Width: 30mm
- Handle Depth: 25mm
-
STANWAY 250mm Mill Bastard File One Round Edge
Used for sharpening mill or circular saws. Has one round edge used for rounding gullets. Single cut used with light pressure for more precision. Has a bastard coarseness; teeth spaced apart.
Specifications:
- Overall Length: 365mm
- Blade Length: 250mm
- Blade Width: 24mm
- Blade Depth: 4.5mm
- Handle Length: 115mm
- Handle Width: 30mm
- Handle Depth: 25mm
-
STANWAY 250mm Round Bastard File
Round in cross-section, primarily used for enlarging holes, and scalloping concave surfaces. Bastard cut for general purpose deburring, sharpening and shaping.
Specifications:
- Overall Length: 365mm
- Blade Length: 250mm
- Blade Width: 9mm
- Blade Depth: 9mm
- Handle Length: 115mm
- Handle Width: 30mm
- Handle Depth: 25mm
-
STANWAY 300mm Aluminium Rafter Square
This trade quality 300mm Stanway Aluminium Rafter Square is precision designed and made from aluminium to ensure strength, durability, and long life. CNC machined edges for guaranteed accuracy. This rafter square has a anodized matte black protective finish with easy-to-read laser etched bold white markings. This square uses metric millimetre markings/measurements. A common rafter conversion table is included on rafter square which has been laser etched on one side. Suitable for all trades people and the serious DIY users.
-
STANWAY 300mm Heavy Duty Combination Square
The Stanway Heavy Duty Combination Square is the perfect tool for your next woodworking, stonemasonry, or metalworking job! This square is designed for many uses such as an outside or inside try square, a mitre square or a depth and marking gauge. Very accurate, reliable, and easy to use. Features a ruler adjustment locking nut, a spirit level and a built-in scriber for surface marking. Durably etched, heavy-duty cast iron ruler is rust resistant and built to last. Blade is marked with metric 1mm graduations on each side of ruler. Suitable for all trades people and the serious DIY users.
-
STANWAY 30m Long Steel Tape
The Stanway Long Steel Tape Measure is engineered with a heavy-duty, impact and shock resistant ABS casing with a protective rubber bumper and a yellow steel blade, protected with a nylon coating. This tape measure is ergonomically designed for high usability due to its strong grip and its 3:1 winding mechanism for faster blade retraction. This tape also features a reinforced hook with a rubberised plastic ring, 31: geared non-finger nipping winding handle, and a fixed hook and ring. Suitable for all trades people and the serious DIY users.
-
STANWAY White Folding Rule (1m x 18mm)
The Stanway White Folding Rule is a versatile and durable tool crafted from hard-wearing ABS plastic. Its clever 4-fold compact design makes it incredibly convenient for storage, fitting easily into toolboxes or pockets when not in use. When unfolded, this rule extends to an impressive 1 meter in length, providing ample reach for various measuring tasks. The 18mm wide blade boasts a bevelled edge, ensuring precise marking on surfaces. Millimeter graduations further enhance its accuracy, making it indispensable for carpenters, craftsmen, and DIY enthusiasts alike. Whether you’re building furniture or tackling home improvement projects, the Stanway White Folding Rule is the ideal companion for accurate and efficient measurements.
-
STARRETT 505A-12 300mm (12″) Aluminium Mitre Protractor
The popular Pro-Site™ 505 protractor family consists of two 300mm (12″) combination protractors, a 300mm (12″) mitre protractor and two 175mm (7″) mitre protractors. The combination protractors take the guesswork out of these functions: mitre cuts, single cuts, compound mitre cuts, included conversion table, protractor and roof pitches. The mitre protractors are ideal for carpenters, plumbers and all building trades that require the measuring and transferring of angles.
-
STARRETT 505P-7 175mm (7″) Plastic Mitre Protractor
The 175mm (7″) Plastic Mitre Protractor takes error-prone calculations out of the process of mitre cuts. This tool is ideal for carpenters, plumbers and all building trades that require the measuring and transferring of angles, plus is invaluable for home use. This hardened plastic mitre protractor offers all the same functionality as the 505A-7 aluminium protractor.
-
Sterling Ultimax Tape Measure 8M x 25mm Metric
Sterling Ultimax Tape Measure 8m x 25mm Metric
Premium rubber grip
Double sided blade printing
High impact resistant ABS casing with non-slip grip
Reinforced 4 rivet dual-hook
25mm wide blade for super standout
Superior internal mechanism for smooth operation
Layered nylon blade for maximum durability
-
STILETTO FB11G 11-1/2″ Titanium Glazer Bar
The STILETTO® 11-1/2″ Titanium Glazer Bar is strong and lightweight. It is recommended for setting windows and doors, moderate prying, and scraping. This Glazer Bar features a 180° side nail puller that allows you to pull 6D-16D nails with ease.
- 8.5oz Solid Titanium Bar with Strong Arch Design
- Staple Puller Grabs 3/16″ Pre-Hung Door Staples Easily
- Two “Multi-Fulcrum” Nail Pullers Designed to Increase Leverage
- Built-In Bottle Opener
-
STILETTO FH10C 10oz Smooth/Curved Hickory Hammer
The STILETTO® 10oz Titanium Hickory Finish Hammer with Smooth Face and 14.5″ Curved Handle is made with shock-absorbing USA Hickory. This 10oz titanium hammer hits like a 16oz steel hammer with 45% less weight and 10x less recoil shock. It is recommended for finish carpentry, remodeling, and light framing. The Titanium Hickory Finish Hammer includes a magnetic nail starter and replaceable handle.
- 10oz Titanium Head Hits Like a 16oz Steel Head
- Replaceable USA Made Hickory Handle
- Magnetic Nail Starter
- Straight Claw Design
-
STILETTO TB3SC TIBONE™ III Smooth/Curve Titanium
The STILETTO® 15oz TIBONE™ III Hammer with Smooth Steel Face and 18″ Curved Handle is our most powerful and most durable hammer. This 15oz full titanium hammer hits like a 28oz steel hammer, with 45% less weight and 10x less recoil shock. It is recommended for rough framing, remodeling, and pole barn construction. The TIBONE™ III features a 180° side nail puller that allows you to pull 6D-16D nails with ease and includes a magnetic nail starter.
-
STILETTO TBRG-G Green Replacement Grip
The STILETTO® Green Replacement Grip extends the life of your hammer while providing a personal touch. It is easy to install and remove on the jobsite with minimal tools. The STILETTO® Replacement Grip is available in 5 colors and includes a Black Oxide T25 Bolt, Nylon Locking Nut, and External Tooth Lock Washer.
-
STILETTO TBRG-O Orange Replacement Grip
The STILETTO® Orange Replacement Grip extends the life of your hammer while providing a personal touch. It is easy to install and remove on the jobsite with minimal tools. The STILETTO® Replacement Grip is available in 5 colors and includes a Black Oxide T25 Bolt, Nylon Locking Nut, and External Tooth Lock Washer.
-
STILETTO TBRG-Y Hi-Vis Yellow Replacement Grip
The STILETTO® Hi-Vis Yellow Replacement Grip extends the life of your hammer while providing a personal touch. It is easy to install and remove on the jobsite with minimal tools. The STILETTO® Replacement Grip is available in 5 colors and includes a Black Oxide T25 Bolt, Nylon Locking Nut, and External Tooth Lock Washer.
-
STILETTO TI14SC 14oz Smooth/Curved Hickory
The STILETTO® 14oz Titanium Hickory Hammer with Smooth Face and 18″ Curved Handle is made with shock-absorbing USA Hickory. This 14oz titanium hammer hits like a 24oz steel hammer with 45% less weight and 10x less recoil shock. It is recommended for rough framing and remodeling. The Titanium Hickory Hammer includes a magnetic nail starter and replaceable handle.
- 14oz Titanium Head Hits Like a 24oz Steel Head
- Replaceable USA Made Hickory Handle
- Magnetic Nail Starter
- Straight Claw Design
-
STILETTO TI16SC 16oz Smooth/Curved Hickory
The STILETTO® 16oz Titanium Hickory Hammer with Smooth Face and 18″ Curved Handle is made with shock-absorbing USA Hickory. This 16oz titanium hammer hits like a 28oz steel hammer with 45% less weight and 10x less recoil shock. It is recommended for rough framing and remodeling. The Titanium Hickory Hammer includes a magnetic nail starter and replaceable handle.
- 16oz Titanium Head Hits Like a 28oz Steel Head
- Replaceable USA Made Hickory Handle
- Magnetic Nail Starter
- Straight Claw Design
-
STILETTO TIB14RSC 14oz TIBONE™ Smooth/Curved Titanium
The STILETTO® 14oz TIBONE™ Hammer with Smooth Steel Face and Curved Handle is our most powerful and most durable hammer. This All-Titanium hammer is 45% less weight and hits like steel. The durable TIBONE™ design is best for framing and pulling nails. The 180° Side Nail Puller and Magnetic Nail Starter fit up to 16D and Duplex Nails. The TIBONE™ features a replaceable steel face and multiple grip colors, extending the life of the hammer and providing a personal touch.
-
STILETTO TIB15SC 15oz TIBONE™ Smooth/Curved Titanium
The STILETTO® 15oz TIBONE™ Hammer with Smooth Steel Face and Curved Handle is our most powerful and most durable hammer. This All-Titanium hammer is 45% less weight and hits like steel. The durable TIBONE™ design is best for framing and pulling nails. The 180° Side Nail Puller and Magnetic Nail Starter fit up to 16D and Duplex Nails. The TIBONE™ features a replaceable steel face and multiple grip colors, extending the life of the hammer and providing a personal touch.
-
STILETTO TICLW-12 11-1/2″ Titanium Clawbar
The STILETTO® 11-1/2″ Titanium Dimpler® Nail Puller includes the patented nail removal feature for pulling common nails easily. It is recommended for setting windows and doors, moderate prying, and scraping. This Clawbar features a 180° side nail puller that allows you to pull 6D-16D nails with ease.
- 8.5oz Solid Titanium Bar with Lightweight Open Truss Design
- Dimpler® Nail Removal Feature Makes a Round Impression Around the Nail Head to Allow Claws to Slip Easily Under the Nail Head, Reducing Damage to the Material
- Strike Plate Outlasts Steel Bars by 3X and Doesn’t Spall Crack or Mushroom like Steel Bars
- Two “Multi-Fulcrum” Nail Pullers Designed to Increase Leverage
-
STILETTO TRMB 10oz TRIMBONE™ Smooth/Curve Titanium
The STILETTO® 10oz TRIMBONE™ Hammer with Smooth Steel Face and Curved Handle is designed for finish with specialized features. This titanium hammer is 45% less weight and hits like steel. The compact D-Face and Trim Claw are ideal for tight spaces. The TRIMBONE™ also features a steel face and a replaceable colored grip, available in 6 colors, extending the life of the hammer and providing a personal touch. The 180° side nail puller is ideal for 2D-10D nails but has the power to pull up to 16D.
-
STILETTO TRMB-RMA TRIMBONE™ Mallet Cap Kit
The STILETTO® TRIMBONE™ Mallet Cap Kit replaces the need for most mallet applications. Easily alternate between hammer and mallet when in need of a light touch. The non-marring Mallet Cap comes in White (Hard Mallet) and Black (Soft Mallet).
- Non-Marring
- Quick Removal
- Available in White (Hard Mallet) and Black (Soft Mallet)
- Fits: TRIMBONE™ TRMB
-
SUTTON NAIL PUNCH SET- 5PC
Sutton Tools Nail Punches are a short steel rod, usually tapered; used to drive a nail or brad below, or flush with, a wood surface.
All Sutton Tools punches are made from high quality chrome vanadium steel with a hardened and tempered point to withstand continuous use. An ergonomic soft rubber grip provides comfort and safety.
INCLUDES SIZES: 2, 3, 4, 5, 6mm
-
SUTTON PIN PUNCH SET
Sutton Tools Pin Punches are used as a driving tool, typically, as the name implies, to drive pins that are used to affix a fixture to a rotating shaft.
All Sutton Tools punches are made from high quality chrome vanadium steel with a hardened and tempered point to withstand continuous use. An ergonomic soft rubber grip provides comfort and safety.
-
SYKES-PICKAVANT 800101 – MOTORQ PROFESSIONAL TORQUE WRENCH 1/2”
- Soft feel ergonomic handle that provides exceptional grip even in oily conditions
- Large easy to read dual scale for improved visibility, precise torque setting adjusts 40% faster
- Push/pull torque adjustment knob that allows for rapid and accurate torque settings
- Unique Timestrip® feature that provides a visual indication of when the torque wrench is due for re-calibration
- Features the renowned Sykes-Pickavant mechanism with push-thru ratchet head that has been engineered for strength and durability while operating in both clockwise and anti-clockwise directions
- All Sykes-Pickavant torque wrenches are manufactured in England to ISO9000:2000 standard and are supplied with a UKAS accredited calibration certificate in a protective case
-
SYKES-PICKAVANT 800200 – MOTORQ PROFESSIONAL TORQUE WRENCH 1/2”
- Soft feel ergonomic handle that provides exceptional grip even in oily conditions
- Large easy to read dual scale for improved visibility, precise torque setting adjusts 40% faster
- Push/pull torque adjustment knob that allows for rapid and accurate torque settings
- Unique Timestrip® feature that provides a visual indication of when the torque wrench is due for re-calibration
- Features the renowned Sykes-Pickavant mechanism with push-thru ratchet head that has been engineered for strength and durability while operating in both clockwise and anti-clockwise directions
- All Sykes-Pickavant torque wrenches are manufactured in England to ISO9000:2000 standard and are supplied with a UKAS accredited calibration certificate in a protective case
-
Teng 1/2in Dr. 400mm Long Arm Ratchet 60T
• 400mm long handle for added torque when needed
• 45 teeth giving 8 degree increments between clicks
• Twist reverse for quickly and easily changing between tightening and loosening
• Quick release for easier changing between different sockets and accessories
• Bi-material grip for extra comfort
-
Teng 1/2in Dr. FRP Ratchet 45T DIN3122D
1200FRP – 1/2in Drive FRP Ratchet
Teng Tools steel reinforced fibre ratchets have been designed to create a 45 teeth (8 degree increment) ratchet with quick release and flip reverse to meet or exceed all internationally recognised quality and torque specifications. The design protected ratchet (24583ROC) is not only lighter and just as strong but is also much more comfortable to use than regular ratchets. New style bi-material handles for a more comfortable grip.
Max Torque: 512Nm Length: 255mm Weight: 358gm
All Teng Tools ratchets should be cleaned and maintained on a regular basis to reduce wear and to prolong life. However, with all tools involving moving parts some wear will occur with time. Teng Tools offer a full range of complete service kits and spare parts for their ratchets – full details available from your local Teng Tools stockist.
-
Teng 1/2in Dr. Torque Wrench 40-210Nm / 30-150ft/lb
Torque wrench manufactured to DIN3122 spec. With ratchet, the torque wrench can be used for both tightening, and final checking of the torque. Reversible with lever, but only for right-hand action torque checking. Equipped with angular gauge for after tightening. Dual scale Nm & ft/lb. Lockable setting. Accuracy ±4%. Supplied with factory calibration certificate.
-
Teng 1/2in Dr. Torque Wrench 70-350Nm / 50-250ft/lb
Torque wrench according to DIN3122. With ratchet, the torque wrench can be used for both tightening, and final checking of the torque. Reversible with lever, but only for right-hand action torque checking. Equipped with angular gauge for after tightening. Dual scale Nm & ft/lb. Lockable setting. Accuracy ±4%. Supplied with factory calibration certificate.
-
Teng 1/4in Dr. FRP Ratchet 45T DIN3122D
1400FRP – 1/4in Drive FRP Ratchet Teng Tools steel reinforced fibre ratchets have been designed to create a 45 teeth (8 degree increment) ratchet with quick release and flip reverse to meet or exceed all internationally recognised quality and torque specifications. The design protected ratchet (24583ROC) is not only lighter and just as strong but is also much more comfortable to use than regular ratchets. Bi-material handles for a more comfortable grip.
Max Torque: 62Nm Length: 150mm Weight: 96gm
All Teng Tools ratchets should be cleaned and maintained on a regular basis to reduce wear and to prolong life. However, with all tools involving moving parts some wear will occur with time. Teng Tools offer a full range of complete service kits and spare parts for their ratchets – full details available from your local Teng Tools stockist.
-
Teng 1/4in Dr. Torque Screwdriver 1-5Nm**
Torque Screwdriver
• For precision tightening of screws and bolts.
• For right hand action.
• With 1/4″ drive and adapter for 1/4″ bits.
• Suitable for e.g. fine mechanics, electronics, etc.
• Tolerance ±6%
• Supplied in plastic box.
Torque Range ISO: 1-5 Nm
Drive for Bits: 1/4 inch
-
Teng 1/4in Dr. Torque Wrench 5-25Nm / 4-18ft/lb
Torque wrench according to DIN3122. With ratchet, the torque wrench can be used for both tightening, and final checking of the torque. Reversible with lever, but only for right-hand action torque checking. Equipped with angular gauge for after tightening. Dual scale Nm & ft/lb. Lockable setting. Accuracy ±4%. Supplied with factory calibration certificate.
Specification:
• Range – 5-25Nm (4-18 ft/lb)
• Scale – 0.4Nm (0.4 ft/lb)
• Overall Length – 277mm
• Weight – 580gm
** After use ALWAYS return torque setting to zero **
-
Teng 1/4in Long Ratchet Flexible Head 43 Teeth 200mm
Features
• 200mm long handle for added torque when needed.
• Flexible ratchet head with locking mechanism for use at different angles.
• 43 teeth giving 8 degree increments between clicks.
• Twist reverse for quickly and easily changing between tightening and loosening.
• Quick release for easier changing between different sockets and accessories.
• Bi-material grip for extra comfort.
-
Teng 1/4in Ratchet Long Arm 43 Teeth 200mm
• 200mm long handle for added torque when needed.
• 43 teeth giving 8 degree increments between clicks.
• Twist reverse for quickly and easily changing between tightening and loosening.
• Quick release for easier changing between different sockets and accessories.
• Bi-material grip for extra comfort.
-
Teng 105pc 1/2in Dr. Metric H/Duty Vehicle Tool Set
THDV105 | Teng 105pc 1/2in Dr. Metric H/Duty Vehicle Tool Set
The 105 hand tools have been selected to handle the most common maintenance tasks that are carried out on heavy machinery or heavy vehicles. Supplied in a hard wearing portable case making it easy to bring all of the tools required directly to job.
The kit consists of an FRP ratchet, extension bar, 17” flex handle, 6-point ½” drive regular sockets from 8-32 mm, ½” drive hex sockets from 5 to 19 mm, several combination spanners from 8 to 32 mm, adjustable wrenches, pliers, side cutters, bits and bits driver, hex key set, flat screwdriver and either a ball pein hammer or an engineers style hammer depending on the set that you choose.
Designed and manufactured to DIN and ISO standards.
-
Teng 10in / 250mm Wide Jaw Adjustable Wrench
Adjustable wrenches with an extra wide jaw opening. Chrome vanadium steel, a 15° jaw angle, ergonomically designed bi-material handle grip and phosphate finish with a graduated scale on the jaws. Exceeding international standards ISO6787-1982, ASME B.107.8-1996, BS6333-1995, DIN3117-1988, JIS B4604-1976.
• Capacity – 50mm / 2in
• Weight – 440gm
-
Teng 10in Quick Set Pliers Wrench
MB483-10 | Teng 10in Quick Set Pliers Wrench
The TengTools 10-inch quick set pliers wrench MB483-10 is a highly versatile tool tailored for professionals in fields such as automotive repair, plumbing, and general maintenance. This tool effectively eliminates the need for multiple sets of mm and inch spanners, making it a practical asset in any toolkit. Its design prevents surface damage when working with delicate, plated pipe fittings. The tool’s capabilities extend to gripping, holding, pressing, and bending. The parallel jaws are engineered for a firm and consistent grip, providing increased control and efficiency. • Eliminates the need for multiple spanner sets, offering a convenient all-in-one solution
• Ideal for damage-free work on plated fittings, preventing marring or scratching
• Versatile in function, capable of gripping, holding, pressing, and bending
• Parallel jaws design ensures a solid and consistent grip across various applications
Specification
• Capacity: 45mm
• Jaw depth: 35mm
• Tethering facility: No
• Length: 250mm (10in)
• Net weight: 422g
-
Teng 10in/250mm Iq Series Adjustable Wrench
Industrial adjustable wrenches made of chrome vanadium. Exceeding international standards ISOO6787-1982, ASME B.107.8M-1996, BS6333-1995, JISB4604-1976. The 15° jaw allows the wrench to be used in narrow areas as only 30° turning is needed. The wider jaw opening increases the range of bolt sizes that can be fitted. Non protruding on the moveable jaw end gives better access where space is limited. Black phosphate finish with graduated scale and bi-material grip handle.
• Capacity – 33mm / 1-1/4in
• ISO Norm – 320Nm
• Weight – 440gm
-
Teng 11pc Screwdriver Set – Flat | Phillips | Pozi
MD911N | Teng 11pc Screwdriver Set – Flat | Phillips | Pozi • TT-MV PLUS steel blades for added torque. • Bi-material handles for easy use with higher torque and faster speed. • Hole in the handle for hanging or for use as a T-Handle for extra torque or with a fall protection wire if needed. • Designed and manufactured to DIN5264 • Supplied in a handy carrying case.
